View LT1082_142972.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LT1082 1A High Voltage, Efficiency Switching Voltage Regulator
FEATURES
s s s s s s
DESCRIPTIO
s s s
Wide Input Voltage Range: 3V to 75V High Switch Voltage: 100V Low Quiescent Current: 4.5mA Internal 1A Switch Shutdown Mode Draws Only 120A Supply Current Isolated Flyback Regulation Mode for Fully Floating Outputs Can Be Externally Synchronized Available in MiniDIP and TO-220 Packages Same Pinout as LT1072
The LT1082 is a monolithic high voltage switching regulator. It can be operated in all standard switching configurations including buck, boost, flyback, forward, and inverting. A 1A high efficiency switch is included on the die along with all oscillator, control, and protection circuitry. The LT1082 operates with supply voltages from 3V to 75V, switch voltage up to 100V and draws only 4.5mA quiescent current. It can deliver load power up to 20W with no external power devices. By utilizing current-mode switching techniques, it provides excellent AC and DC load and line regulation. An externally activated shutdown mode reduces total supply current to 120A typical for standby operation. Totally isolated and regulated outputs can be generated by using the optional "isolated flyback regulation mode" built into the LT1082, without the need for optocouplers or extra transformer windings. The LT1082 has a unique feature to provide high voltage short-circuit protection. When the FB pin is pulled down to 0.6V and the current out of the pin reaches approximately 350A, the switching frequency will shift down from 60kHz to 12kHz. The LT1082 is nearly identical to the lower voltage LT1072. For the major differences in specifications, see the table on the left.
Telecom 5V Supply Maximum Output Current vs Input Voltage
APPLICATI
s s s
S
Telecom 5V Supply at 0.7A from -48V 90V Supply at 120mA from 15V All Applications Using LT1072 (See Below for Specification Differences)
LT1082 and LT1072 Major Specification Differences
LT1082C LT1072HV 3V to 75V 3V to 60V 100V 75V 1A 1.25A 4.5mA 6mA 60kHz 40kHz 16.2 + 0.6 (35k/RFB) 16 + 0.35 (7k/RFB)
VIN VSW Switch Current Limit Quiescent Current Operating Frequency Flyback Reference Voltage
USER NOTE: This data sheet is only intended to provide specifications, graphs, and a general functional description of the LT1082. Application circuits are included to show the capability of the LT1082. A complete design manual (AN19) and Switcher CAD (LTC Switching Power Supply Design Program) should be obtained to assist in developing new designs. This manual contains a comprehensive discussion of both the LT1070 and the external components used with it, as well as complete formulas for calculating the values of these components. The manual can also be used for the LT1082 by factoring in the lower switch current rating.
Negative-to-Positive Telecom 5V Supply
**250H *D1
MAXIMUM OUTPUT CURRENT (A)
3.83k VIN 33F 80V CHEMI-CON SXE SERIES VSW Q1 2N5401
+
VOUT 5V, 0.7A 470F 10V CHEMI-CON SXE SERIES
NOTE: MAXIMUM OUTPUT CURRENT IS A FUNCTION OF INPUT VOLTAGE. SEE THE GRAPH ON THE RIGHT.
+
GND
LT1082 VC FB 1.1k 4.7k 0.01F 0.22F * MOTOROLA MUR110 (100V, 1A) ** 69 TURNS OF #28 AWG WIRE ON A MICROMETALS T60 TYPE 52 CORE. NOTE: THIS CORE IS LOW COST, BUT HAS HIGHER CORE LOSS AND IS LARGER THAN NECESSARY FOR LOWER CURRENT APPLICATIONS. FOR SMALLER INDUCTORS OR HIGHER EFFICIENCY, USE A LOW LOSS CORE SUCH AS MAGNETICS INC. KOOL M OR MOLYPERMALLOY.
-20V TO -70V
1082 TA01
U
1.0 0.9 0.8 0.7 0.6 0.5 L=100H 0.4 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 INPUT VOLTAGE (V)
1082 TA02
UO
f = 45kHz ISW LIMIT = 1.07A
L=550H L=450H L=350H L=250H
L=150H
1
LT1082 ABSOLUTE AXI U RATI GS
Operating Junction Temperature Range LT1082M ......................................... - 55C to 150C LT1082I ........................................... - 40C to 125C LT1082C ............................................... 0C to 100C Supply Voltage ....................................................... 75V Switch Output Voltage .......................................... 100V Feedback Pin Voltage (Transient, 1ms) ................ 15V Storage Temperature Range ................ - 65C to 150C Lead Temperature (Soldering, 10 sec)................. 300C
PACKAGE/ORDER I FOR ATIO
TOP VIEW GND 1 VC 2 FB 3 NC 4 8 7 6 5 E2 VSW E1 VIN
FRONT VIEW 5 4 3 2 1 Q PACKAGE 5-LEAD DD TJMAX = 100C, JA = 40C/ W (CQ) TJMAX = 125C, JA = 40C/ W (IQ) NOTE: JA VARIES FROM 25C/W TO 50C/W DEPENDING ON BOARD COMPOSITION. VIN VSW GND FB VC
J8 PACKAGE N8 PACKAGE 8-LEAD CERAMIC DIP 8-LEAD PLASTIC DIP
TJMAX = 150C, JA = 100C/W (MJ8) TJMAX = 100C, JA = 90C/W (CN8) TJMAX = 125C, JA = 90C/W (IN8)
ORDER PART NUMBER LT1082MJ8 LT1082CN8 LT1082IN8
ORDER PART NUMBER LT1082CQ LT1082IQ
ELECTRICAL CHARACTERISTICS VIN = 15V, VC = 0.5V, VFB = VREF, output pin open, unless otherwise specified.
SYMBOL VREF IB gm PARAMETER Reference Voltage Feedback Input Current Error Amplifier Transconductance Error Amplifier Source or Sink Current Error Amplifier Clamp Voltage Reference Voltage Line Regulation AV Error Amplifier Voltage Gain Minimum Input Voltage CONDITIONS Measured at Feedback Pin VC = 0.8V VFB = VREF
q q
IC = 25A
q
VC = 1.5V
q
Hi Clamp, VFB = 1V Lo Clamp, VFB = 1.5V 3V VIN VMAX, VC = 0.8V 0.9V VC 1.4V
q q
2
U
U
W
WW
U
W
FRONT VIEW 5 4 3 2 1 T PACKAGE 5-LEAD TO-220 VIN VSW GND FB VC
TJMAX = 100C, JA = 75C/ W, JC = 8C/ W (CT) TJMAX = 125C, JA = 75C/ W, JC = 8C/ W (IT)
ORDER PART NUMBER LT1082CT LT1082IT
MIN
TYP
MAX 1.264 1.274 750 1100 6000 7000 400 400 2.3 0.36 0.03
UNITS V V nA nA mho mho A A V V %/V V/V V
1.224 1.244 1.214 1.244 350 3000 2400 150 120 1.8 0.12 350 4400 200
0.22 650 2.6
3.0
LT1082
ELECTRICAL CHARACTERISTICS VIN = 15V, VC = 0.5V, VFB = VREF, output pin open, unless otherwise specified.
SYMBOL IQ PARAMETER Supply Current Control Pin Threshold Normal/Flyback Threshold on Feedback Pin f Switching Frequency
q
CONDITIONS 3V VIN VMAX, VC = 0.6V Duty Cycle = 0
q
MIN
TYP 4.5
MAX 7.0 1.1 1.25 0.8 70 75
UNITS mA V V V kHz kHz kHz V A/V
0.7 0.5 0.58 50 45 100
0.9 0.67 60 12
800A IFB 450A BV Output Switch Breakdown Voltage Control Voltage to Switch Current Transconductance VFB Flyback Reference Voltage Change in Flyback Reference Voltage Flyback Reference Voltage Line Regulation Flyback Amplifier Transconductance (gm) Flyback Amplifier Source and Sink Current VSAT ILIM Output Switch "On" Resistance (Note 1) Switch Current Limit (LT1082C) Switch Current Limit (LT1082I) Switch Current Limit (LT1082M) IIN ISW DCMAX Supply Current Increase During Switch-On Time Maximum Switch Duty Cycle Flyback Sense Delay Time Shutdown Mode Supply Current Shutdown Mode Threshold Voltage 3V VIN VMAX, VC = 0.05V 3V VIN VMAX
q
3V VIN VMAX, ISW = 1.5mA
q
115 1.5
IFB = 60A
q
17 16 3.5 150
18.6 4.6 0.01 300 32 50 0.8
20.5 21.5 6.5 0.03 500 70 90 1.2 2.6 2.6 2.4 2.8 2.8 2.6 3.0 3.0 2.8 45 97 350 250 300
V V V %/V mho A A A A A A A A A A A mA/A % s A mV mV
60A IFB 200A IFB = 60A, 3V VIN VMAX IC = 10A VC = 0.6V Source IFB = 60A Sink ISW = 0.7A (LT1082C), ISW = 0.5A (LT1082M) Duty Cycle = 20% Duty Cycle 50% Duty Cycle = 80% (Note 2) Duty Cycle = 20% Duty Cycle 50% Duty Cycle = 80% (Note 2) Duty Cycle = 20% Duty Cycle 50% Duty Cycle = 80% (Note 2)
q q q q q q q q q q q q
15 30 1.07 1.0 0.8 0.85 0.8 0.65 0.75 0.7 0.6
35 85 92 1.5 120 150
70 50
The q denotes the specifications which apply over the operating temperature range. Note 1: Measured with VC in hi clamp, VFB = 0.8V.
Note 2: For duty cycles (DC) between 50% and 80%, minimum guaranteed switch current decreases linearly.
3
LT1082
TYPICAL PERFOR A CE CHARACTERISTICS
Suggested Core Size and Inductance for Telecom 5V Supply
79
LOAD CURRENT 100mA 200mA 400mA 600mA 800mA TYPE 52 POWDERED IRON T38 250H T50 250H T60 250H T60 250H T80 350H KOOL M OR MOLYPERMALLOY T38 200H EFFICIENCY (%) T38 150H T50 150H T50 200H T80 350H
1082 GA
70 67 64 61 58 55 0
VIN = -40V
FREQUENCY (kHz)
Short-Circuit Frequency Shift-Down vs Feedback Current
70 60
FREQUENCY (kHz)
TA = 0C TA = 150C
TA = -55C
SWITCH CURRENT (A)
DUTY CYCLE (%)
50 40 30 20 10 0 0
100 200 300 400 500 600 700 800 FEEDBACK CURRENT (A)
1082 G03
Flyback Blanking Time
2.2 2.0 1.8 2.9
SWITCH SATURATION VOLTAGE (V)
MINIMUM INPUT VOLTAGE (V)
TIME (s)
1.6 1.4 1.2 1.0 -75 -50 -25 0 25 50 75 100 125 150 JUNCTION TEMPERATURE (C)
1082 G06
4
UW
Telecom 5V Supply Efficiency
80
Telecom 5V Supply Short-Circuit Frequency Shift-Down
TA = 25C 70 60 50 40 30 20
76 73
VIN = -20V
VIN = -60V
VIN = -70V
L = 250H R = 0.08 2 3 4
10 0 6 5 4 3 2 OUTPUT VOLTAGE (V) 1 0
1082 G02
1
POWER OUTPUT (W) NOTE: THIS GRAPH IS BASED ON LOW CORE LOSS PERMALLOY INDUCTOR. IF POWDERED IRON CORE INDUCTOR IS USED, THE CORE LOSS IS TYPICALLY 100mW HIGHER. 1082 G01
Switch Current Limit
4
Maximum Duty Cycle
97 96
3
95 94 93 92 91
2
TJ = -55C TJ = 150C
TJ = 25C
1
0
0
10 20 30 40 50 60 70 80 90 100 DUTY CYCLE (%)
1082 G04
90 -75 -50 -25 0 25 50 75 100 125 150 175 TEMPERATURE (C)
1082 G05
Minimum Input Voltage
2.00 1.75
Switch Saturation Voltage
2.8 2.7
ISW = 1A
TJ = 150C 1.50 1.25 1.00 0.75 0.50 0.25 0 0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 SWITCH CURRENT (A)
1082 G08
TJ = 100C TJ = 25C
ISW = 0A 2.6 2.5 2.4 2.3 -75 -50 -25
TJ = -50C
0 25 50 75 100 125 150 TEMPERATURE (C)
1082 G07
LT1082
TYPICAL PERFOR A CE CHARACTERISTICS
Isolated Mode Flyback Reference Voltage
25 24 23
FLYBACK VOLTAGE (V)
65
FREQUENCY (kHz)
VREF FREQ
1.245
REFERENCE VOLTAGE CHANGE (mV)
RFB = 3k
22 21 20 19 18 17 16 15 -75 -50 -25 0 25 50 75 100 125 150 175 TEMPERATURE (C)
1082 G09
RFB = 6k RFB = 10k
Feedback Bias Current vs Temperature
800 700
FEEDBACK BIAS CURRENT (nA)
675 650 625 600 575 FEEDBACK PIN CURRENT (AT THRESHOLD) 550 525
-18 -16 -14 -12 -10 -8 -6
SUPPLY CURRENT (A)
VC PIN VOLTAGE (mV)
600 500 400 300 200 100 0 -75 -50 -25 0 25 50 75 100 125 150 175 TEMPERATURE (C)
1082 G12
Supply Current vs Supply Voltage (Shutdown Mode)
200
160
DRIVER CURRENT (mA)
120
VC = 50mV
70 60 50 40 30 20 10
SUPPLY CURRENT (mA)
SUPPLY CURRENT (A)
80
VC = 0V
40
0 0 10 50 60 20 30 40 SUPPLY VOLTAGE (V) 70 80
UW
1082 G15
Reference Voltage and Switching Frequency vs Temperature
70 1.250 5 4 3 2 1 0 -1 -2 -3 -4 -5
Line Regulation
REFERENCE VOLTAGE (V)
60
1.240
TJ = -55C
55
1.235
50
1.230
TJ = 150C TJ = 25C
45 1.225 -75 -50 -25 0 25 50 75 100 125 150 175 TEMPERATURE (C)
1082 G11
0
10
20
30 40 50 60 INPUT VOLTAGE (V)
70
80
Normal/Feedback Mode Threshold on Feedback Pin
750 725 FEEDBACK PIN VOLTAGE (AT THRESHOLD) 700 -24 -22 -20
VC PIN CURRENT (A)
200 180 160 140 120 100 80 60 40 20 0
1082 G10
Shutdown Mode Supply Current
-55C TJ 125C
TJ = 150C
500 -4 -75 -50 -25 0 25 50 75 100 125 150 175 TEMPERATURE (C)
1082 G16
0
10 20 30 40 50 60 70 80 90 100 VC PIN VOLTAGE (mV)
1082 G17
Driver Current* vs Switch Current
100 90 80
Supply Current vs Input Voltage**
14 13 12 11 10 9 8 7 6 5 4 3 2 0% DUTY CYCLE 50% DUTY CYCLE 10% DUTY CYCLE 90% DUTY CYCLE
0
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 SWITCH CURRENT (A)
0
10
20
30 40 50 60 INPUT VOLTAGE (V)
70
80
* AVERAGE SUPPLY CURRENT = I Q + DC(2.9 + 10 -2 ISW + 10 -5 ISW2) IQ = QUIESCENT CURRENT, DC = DUTY CYCLE, 1082 G13 ISW = SWITCH CURRENT
**UNDER VERY LOW OUTPUT CURRENT CONDITIONS, DUTY CYCLE FOR MOST CIRCUITS WILL APPROACH 1082 G14 10% OR LESS.
5
LT1082
TYPICAL PERFOR A CE CHARACTERISTICS
Error Amplifier Transconductance
5000 4500
TRANSCONDUCTANCE (mho)
gm =
I (VC PIN) V (FB PIN)
IDLE SUPPLY CURRENT (mA)
4000
300
VC VOLTAGE (mV)
3500 3000 2500 2000 1500 1000 500 0 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C)
1082 G18
Feedback Pin Clamp Voltage
800 700
500 450
FEEDBACK VOLTAGE (mV)
SWITCH CURRENT (A)
600 TJ = 25C 500 400 300 200 TJ = 150C
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 FEEDBACK CURRENT (mA)
1082 G21
VC Pin Characteristics
400 300 TJ = 25C
TRANSCONDUCTANCE (mho)
VC PIN CURRENT (A)
200 100 0 -100 -200 -300 -400 0
VFB = 0.8V (CURRENT OUT OF VC PIN)
0.5
6
UW
Shutdown Thresholds
400 350 CURRENT (OUT OF VC PIN) -400 -350 -300
VC CURRENT (A)
Idle Supply Current vs Temperature
10 9 8 7 6 5 4 3 2 1 -75 -50 -25 0 25 50 75 100 125 150 175 TEMPERATURE (C)
1082 G20
VC = 0.6V
250 200 VOLTAGE AT VC PIN 150 100 50
-250 -200 -150 -100 -50
VIN = 75V VIN = 3V
0 0 -75 -50 -25 0 25 50 75 100 125 150 175 TEMPERATURE (C)
1082 G19
Switch "Off" Characteristics
A. VIN = 3V B. VIN = 15V C. VIN = 40V D. VIN = 55V E. VIN = 75V
TJ = -55C
400 350 300 250 200 150 100 50 0 0
A
B
C
D
E
10 20 30 40 50 60 70 80 90 100 SWITCH VOLTAGE (V)
1082 G22
Transconductance of Error Amplifier
7000 6000 5000 4000 3000 2000 1000 0 -1000 1k 10k 100k 1M FREQUENCY (Hz) gm -30 0 30 60 90 120 150 180 210 10M
1082 G24
VFB = 1.5V (CURRENT INTO VC PIN)
PHASE (DEG)
1.5 2.0 1.0 V C PIN VOLTAGE (V)
2.5
1082 G23
LT1082
BLOCK DIAGRA
FB
1.24V REF
OPERATIO
The LT1082 is a current mode switcher. This means that switch duty cycle is directly controlled by switch current rather than by output voltage. Referring to the block diagram, the switch is turned "on" at the start of each oscillator cycle. It is turned "off" when switch current reaches a predetermined level. Control of output voltage is obtained by using the output of a voltage sensing error amplifier to set current trip level. This technique has several advantages. First, it has immediate response to input voltage variations, unlike ordinary switchers which have notoriously poor line transient response. Second, it reduces the 90 phase shift at mid-frequencies in the energy storage inductor. This greatly simplifies closedloop frequency compensation under widely varying input voltage or output load conditions. Finally, it allows simple pulse-by-pulse current limiting to provide maximum switch protection under output overload or short conditions. A
+
-
W
VIN 16.2V SWITCH OUT 2.3V REG FLYBACK ERROR AMP OSC 60kHz 14kHz LOGIC DRIVER MODE SELECT COMP ANTI-SAT
+
VC CURRENT AMP GAIN 5 SHUTDOWN CIRCUIT 0.2 0.2
ERROR AMP
-
E1* E2
0.15V
* ALWAYS CONNECT E1 TO GROUND PIN ON MiniDIP PACKAGE. EMITTERS TIED TO GROUND ON TO-220 PACKAGE.
GND
1082 BD
U
low dropout internal regulator provides a 2.3V supply for all internal circuitry on the LT1082. This low dropout design allows input voltage to vary from 3V to 75V with virtually no change in device performance. A 60kHz oscillator is the basic clock for all internal timing. It turns "on" the output switch via the logic and driver circuitry. Special adaptive anti-sat circuitry detects onset of saturation in the power switch and adjusts driver current instantaneously to limit switch saturation. This minimizes driver dissipation and provides very rapid turn-off of the switch. A 1.2V bandgap reference biases the positive input of the error amplifier. The negative input is brought out for output voltage sensing. This feedback pin has a second function: when pulled low with an external resistor and with IFB of 60A to 200A, it programs the LT1082 to
7
LT1082
OPERATIO
disconnect the main error amplifier output and connects the output of the flyback amplifier to the comparator input. The LT1082 will then regulate the value of the flyback pulse with respect to the supply voltage. This flyback pulse is directly proportional to output voltage in the traditional transformer coupled flyback topology regulator. By regulating the amplitude of the flyback pulse, the output voltage can be regulated with no direct connection between input and output. The output is fully floating up to the breakdown voltage of the transformer windings. Multiple floating outputs are easily obtained with additional windings. A special delay network inside the LT1082 ignores the leakage inductance spike at the leading edge of the flyback pulse to improve output regulation. When IFB drawn out of the FB pin reaches 350A, the LT1082 shifts the switching frequency down to 12kHz. This unique feature provides high voltage short-circuit protection in systems like the telecom 5V supplies with input voltages down to - 70V; lower frequency is needed under short-circuit conditions with current mode switchers because minimum "on" time cannot be forced below the internally set blanking time. Referring to the telecom 5V supply circuit on the front page, with output shorted to ground, the VFB stays at 0.6V when sourcing IFB up to 1mA. If the FB pin is forced to source more than 1mA, the frequency shifting function may be defeated. Therefore, the minimum suggested value for RFB is 1k and the maximum suggested value is 1.2k. Also, no capacitance more than 1nF should be used on the FB pin, because it may cause unstable switching frequency in this low frequency mode. The error signal developed at the comparator input is brought out externally. This pin (VC) has four different functions. It is used for frequency compensation, current limit adjustment, soft starting, and total regulator shutdown. During normal regulator operation this pin sits at a voltage between 0.9V (low output current) and 2V (high output current). The error amplifiers are current output (gm) types, so this voltage can be externally clamped for adjusting current limit. Likewise, a capacitor-coupled external clamp will provide soft start. Switch duty cycle goes to zero if the VC pin is pulled to ground through a diode, placing the LT1082 in an idle mode. Pulling the VC pin below 0.15V causes total regulator shutdown, with
8
U
only 120A supply current for shutdown circuitry biasing. See AN19 for full application details. Extra Pins on the MiniDIP Packages The miniDIP LT1082 has the emitters of the power transistor brought out separately from the ground pin. This eliminates errors due to ground pin voltage drops and allows the user to reduce switch current limit by a factor of 2:1 by leaving the second emitter (E2) disconnected. The first emitter (E1) should always be connected to the ground pin. Note that switch "on" resistance doubles when E2 is left open, so efficiency will suffer somewhat when switch currents exceed 100mA. Also, note that chip dissipation will actually increase with E2 open during normal load operation, even though dissipation in current limit mode will decrease. See "Thermal Considerations." Thermal Considerations When Using the MiniDIP Packages The low supply current and high switch efficiency of the LT1082 allow it to be used without a heat sink in most applications when the TO-220 package is selected. This package is rated at 50C/W. The miniDIPs, however, are rated at 100C/W in ceramic (J) and 90/W in plastic (N). Care should be taken for miniDIP applications to ensure that the worst case input voltage and load current conditions do not cause excessive die temperatures. The following formulas can be used as a rough guide to calculate LT1082 power dissipation. For more details, the reader is referred to Application Note 19 (AN19), "Efficiency Calculations" section. Average supply current (including driver current) is: IIN 4.5mA + ISW (0.004 + DC/28) ISW = switch current DC = switch duty cycle Switch power dissipation is given by: PSW = (ISW)2 * RSW * DC RSW = LT1082 switch "on" resistance (1.2 maximum)
LT1082
OPERATIO
Total power dissipation is the sum of supply current times input voltage plus switch power: PTOT = (IIN)(VIN) + PSW In a typical example, using negative-to-positive converter to generate 5V at 0.5A from a - 45V input, duty cycle is approximately 12%, and switch current is about 0.5A, yielding: IIN = 4.5mA + 0.5(0.004 + DC/28) = 8.7mA PSW = (0.5)2 * 1.2 * (0.12) = 0.036W PTOT = (45V)(8.7mA) + 0.036 = 0.43W Temperature rise in a plastic miniDIP would be 90C/W times 0.43W, or approximately 39C. The maximum ambient temperature would be limited to 100C (commercial temperature limit) minus 39C, or 61C. In most applications, full load current is used to calculate die temperature. However, if overload conditions must also be accounted for, four approaches are possible. First, if loss of regulated output is acceptable under overload conditions, the internal thermal limit of the LT1082 will protect the die in most applications by shutting off switch current. Thermal limit is not a tested parameter, however, and should be considered only for noncritical applications with temporary overloads. A second approach is to use the larger TO-220 (T) package which, even without a heat sink, may limit die temperatures to safe levels under overload conditions. In critical situations, heat sinking of these packages is required; especially if overload conditions must be tolerated for extended periods of time. The third approach for lower current applications is to leave the second switch emitter (miniDIP only) open. This increases switch "on" resistance by 2:1, but reduces switch current limit by 2:1 also, resulting in a net 2:1 reduction in I2R switch dissipation under current limit conditions. The fourth approach is to clamp the VC pin to a voltage less than its internal clamp level of 2V. The LT1082 switch current limit is zero at approximately 1V on the VC pin and 1.6A at 2V on the VC pin. Peak switch current can be externally clamped between these two levels with a diode. See AN19 for details.
U
LT1082 Synchronizing The LT1082 can be externally synchronized in the frequency range of 75kHz to 90kHz. This is accomplished as shown in the accompanying figures. Synchronizing occurs when the VC pin is pulled to ground with an external transistor. To avoid disturbing the DC characteristics of the internal error amplifier, the width of the synchronizing pulse should be under 1s. C2 sets the pulse width at 0.6s. The effect of a synchronizing pulse on the LT1082 amplifier offset can be calculated from:
KT VC ( tS )( fS) IC + q R3 VOS = IC
KT/q = 26mV at 25C tS = pulse width fS = pulse frequency IC = LT1082 VC source current ( 200A) VC = LT1082 operating VC voltage (1V to 2V) R3 = resistor used to set mid-frequency "zero" in LT1082 frequency compensation network. With tS = 0.6s, fS = 80kHz, VC = 1.5V, and R3 = 2k, offset voltage shift is 5mV. This is not particularly bothersome, but note that high offset could result if R3 were reduced to a much lower value. Also, the synchronizing transistor must sink higher currents with low values of R3, so larger drives may have to be used. The transistor must be capable of pulling the VC pin to within 100mV of ground to ensure synchronizing.
Synchronizing the LT1082
VIN LT1082 GND VC C2 350pF
R3 VN2222* C1
D1 1N4148 R2 2.2k
D2 1N4148
FROM 5V LOGIC
*SILICONIX OR EQUIVALENT
1082 OP01
9
LT1082
TYPICAL APPLICATI
VIN 30V to 70V
VIN 15V
25F
10
UO
+
+
S
Totally Isolated Converter
1.24:1 25V LPRI 500H 1 1 MUR110 15V AT 0.3A 200F COM
+ +
200F
MUR110 VIN 25F LT1082 FB GND VC 3k 0.01F 7k VSW
-15V AT 0.3A MUR110
MINIMUM LOAD OF 0.15A IS REQUIRED FOR EACH OUTPUT. (SEE AN19)
1082 TA03
Boost Converter
1mH, 1A MUR110
VOUT 90V AT 120mA 78.8k
VIN LT1082
VSW FB
+
100F
GND
VC
4.7k
0.033F
1.1k
0.22F
1082 TA04
LT1082
PACKAGE DESCRIPTIO
0.290 - 0.320 (7.366 - 8.128)
CORNER LEADS OPTION (4 PLCS)
0.008 - 0.018 (0.203 - 0.460) 0.385 0.025 (9.779 0.635)
0 - 15
0.023 - 0.045 (0.58 - 1.14) HALF LEAD OPTION 0.045 - 0.065 (1.14 - 1.65) FULL LEAD OPTION 0.045 - 0.065 (1.14 - 1.65) 0.014 - 0.026 (0.360 - 0.660)
0.300 - 0.320 (7.620 - 8.128)
0.009 - 0.015 (0.229 - 0.381)
0.065 (1.651) TYP 0.125 (3.175) MIN 0.020 (0.508) MIN
(
+0.025 0.325 -0.015 +0.635 8.255 -0.381
)
0.045 0.015 (1.143 0.381) 0.100 0.010 (2.540 0.254)
0.060 (1.524)
(
+0.012 0.331 -0.020
+0.305 8.407 -0.508
)
0.067 0.010 (1.702 0.254) 0.032 0.008 (0.813 0.203)
(
+0.012 0.143 -0.020
+0.305 3.632 -0.508
)
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
U
Dimensions in inches (milimeters) unless otherwise noted.
J8 Package 8-Lead Ceramic DIP
0.200 (5.080) MAX 0.015 - 0.060 (0.381 - 1.524)
0.005 (0.127) MIN
0.405 (10.287) MAX 8 7 6 5
0.025 (0.635) RAD TYP 0.125 3.175 0.100 0.010 MIN (2.540 0.254) 1 2 3
0.220 - 0.310 (5.588 - 7.874)
4
N8 Package 8-Lead Plastic DIP
0.045 - 0.065 (1.143 - 1.651) 0.130 0.0 (3.302 0.127) 0.400 (10.160) MAX 8 7 6 5
0.250 0.010 (6.350 0.254)
1
2
3
4
0.018 0.003 (0.457 0.076)
Q Package 5-Lead Plastic DD
0.401 0.015 (10.185 0.381) 15 TYP
0.175 0.008 (4.445 0.203)
0.050 0.008 (1.270 0.203) +0.008 0.004 -0.004
0.059 (1.499) TYP
(
+0.203 0.102 -0.102
)
0.105 0.008 (2.667 0.203)
0.022 0.005 (0.559 0.127)
0.050 0.012 (1.270 0.305)
11
LT1082
PACKAGE DESCRIPTIO
0.380 - 0.420 (9.652 - 10.668) 0.139 - 0.153 (3.531 - 3.886) DIA
0.560 - 0.650 (14.224 - 16.510) 0.866 - 0.913 (21.996 - 23.190)
0.057 - 0.077 (1.448 - 1.956)
12
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7487
(408) 432-1900 q FAX: (408) 434-0507 q TELEX: 499-3977
U
Dimensions in inches (milimeters) unless otherwise noted.
T Package 5-Lead TO-220
0.169 - 0.185 (4.293 - 4.699)
0.079 - 0.135 (2.007 - 3.429)
0.035 - 0.055 (0.889 - 1.397)
0.460 - 0.500 (11.68 - 12.70)
0.620 0.020 (15.75 0.508) 0.700 - 0.728 (17.780 - 18.491)
0.970 - 1.050 (24.64 - 26.67)
0.015 - 0.025 (0.381 - 0.635) 0.210 - 0.240 (5.334 - 6.096)
0.055 - 0.090 (1.397 - 2.286) 0.079 - 0.115 (2.007 - 2.921)
T5 (FORMED) 0392
0.028 - 0.035 (0.711 - 0.889)
LT/GP 0193 10K REV 0
(c) LINEAR TECHNOLOGY CORPORATION 1993

▲Up To Search▲

Price & Availability of LT1082

	To Download LT1082 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .